Category: 60811-18-9

Synthetic Route of 60811-18-9, In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact. 60811-18-9, name is 4-Bromo-1-chloro-2-fluorobenzene belongs to chlorides-buliding-blocks compound, it is a common compound, a new synthetic route is introduced below.

(7) Metal magnesium in an amount of 12 g was suspended in 10 ml of THF under nitrogen gas stream, and a solution prepared by dissolving 10.3 g of 3-fluoro-4-chloro-bromobenzene in 50 ml of THF was added dropwise thereto and stirred at room temperature for 1 hour to prepare a solution of Grignard reagent. In 50 ml of THF was dissolved 10.6 of the 4-(2-(trans-4-(2-(4-n-propylphenyl)ethyl)cyclohexyl)ethyl)iodobenzene, and 1 g of palladium chloride was added thereto and stirred under a reflux. The solution of Grignard reagent prepared in the previous procedures was added dropwise thereto and reacted while stirring for 2 hours. Reaction solution thus obtained was added to 200 ml of dilute hydrochloric acid, and the product was extracted with 200 ml of heptane. Organic layer was washed with water and dried over anhydrous magnesium sulfate, and the solvent was distilled off under a reduced pressure to obtain a yellow-brown oily product. This product was purified by a column chromatography over an alumina by using heptane as an eluent, and further recrystallized from heptane to obtain 2 g of the subject compound. According to the procedures mentioned above, the following Compounds No. 128 to 189 were synthesised:

In the field of chemistry, the synthetic routes of compounds are constantly being developed and updated. I will also mention this compound in other articles, 4-Bromo-1-chloro-2-fluorobenzene, other downstream synthetic routes, hurry up and to see.

Reference:
Patent; Chisso Corporation; US5858275; (1999); A;,
Chloride – Wikipedia,
Chlorides – an overview | ScienceDirect Topics

Some common heterocyclic compound, 60811-18-9, name is 4-Bromo-1-chloro-2-fluorobenzene, molecular formula is C6H3BrClF, traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc, below Introduce a new synthetic route. name: 4-Bromo-1-chloro-2-fluorobenzene

[Example 23] (Preparation of 4′-(trans-4-n-pentyl-4-silacyclohexyl)-4-chloro-3-fluorobiphenyl) 6.5 g (20 mmol) of p-(trans-4-n-pentyl-4-silacyclohexyl) bromobenzene was dripped into a mixture of 0.5 g of magnesium (21 mmol) and 30 ml of THF to obtain a Grignard’s reagent. This solution was then dripped into a 50 ml THF solution of 4.2 g (20 mmol) of 4-chloro-3-fluoro-1-bromobenzene and a catalytic amount of tetrakis (triphenylphosphine) palladium (0) to obtain 4′-(trans-4-n-pentyl-4-silacyclohexyl)-4-chloro-3-fluorobiphenyl. This was then purified by means of chromatography to obtain 6.8 g of the target product (yield 98%). IR (liquid film) numax: 2953, 2916, 2870, 2108, 1479, 1396, 1200, 985, 879 and 812 cm-1

These compound has a wide range of applications. It is believed that with the continuous development of the source of the synthetic route 60811-18-9, its application will become more common.

Reference:
Patent; Shin-Etsu Chemical Co., Ltd.; US5659059; (1997); A;,
Chloride – Wikipedia,
Chlorides – an overview | ScienceDirect Topics

Reference of 60811-18-9,Some common heterocyclic compound, 60811-18-9, name is 4-Bromo-1-chloro-2-fluorobenzene, molecular formula is C6H3BrClF, traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc, below Introduce a new synthetic route.

a. 4-chloro-3-fluorobenzoylpropionic acid To a solution of succinic anhydride (6.0 g) in tetrahydrofuran (60 ml) was added dropwise the Grignard prepared from 1.5 g (0.062 mole) of magnesium turnings and 10.5 g (0.05 mole) of 1-bromo-4-chloro-3-fluorobenzene using the procedure of part a. When the addition was completed, the resulting suspension was stirred for 2 hours at 45 C. after which water (100 ml) was added slowly and the resulting mixture was acidified with concentrated hydrochloric acid to pH=1. The ether layer was separated and extracted with 5% aqueous sodium hydroxide (3*100 ml). The combined aqueous solutions were washed with ether (1*100 ml). The combined basic aqueous layers were acidified with concentrated hydrochloric acid to pH 1 and extracted with ethyl acetate (3*150 ml). The combined organic extracts were washed with water (1*150 ml) and brine (1*150 ml), dried over anhydrous magnesium sulfate and evaporated in vacuo to give 7.1 g (62%) of the product as a yellow orange solid. The resulting acid was converted to the desired product using the procedure of Example 11d-e. Compound 83 was prepared following essentially the same procedure.

The synthetic route of 60811-18-9 has been constantly updated, and we look forward to future research findings.

Reference:
Patent; Rohm and Haas Company; US5552409; (1996); A;,
Chloride – Wikipedia,
Chlorides – an overview | ScienceDirect Topics

In the chemical reaction process, reaction time, type of solvent, can easily affect the result of the reaction, thereby determining the yield and properties of the reaction product. An updated downstream synthesis route of 60811-18-9 as follows. Recommanded Product: 60811-18-9

A] stirred solution of 4-bromo-1- chloro-2-fluorobenzene (25g, 0. 119mol) and triisopropylborate (30. 5ml, 0.131 mol) in dry THF [(500ML)] under argon is cooled [TO-100C] and n-butyllithium (52. [5ML] of a 2.5M solution in hexanes, 0.131 mol) is added dropwise over [15MIN.] The reaction mixture is allowed to warm gradually to room temperature over 18h before it is quenched by the addition of 2M hydrochloric acid (250ml) and stirred at room temperature overnight. The THF is removed under reduced pressure, the aqueous residue is diluted with water [(500ML)] and the mixture is extracted with diethyl ether (3 x [200ML).] The combined ether extracts are washed with saturated brine [(200MOI),] dried [(MGS04),] filtered, evaporated and [DRIED IN VACUO TO] give a colourless solid-a mixture of 4-Chloro-3-fluorobenzeneboronic acid and the functionally equivalent [CYCLOTRIBOROXANE.]

According to the analysis of related databases, 60811-18-9, the application of this compound in the production field has become more and more popular.

Reference:
Patent; NOVARTIS AG; NOVARTIS PHARMA GMBH; WO2004/33435; (2004); A1;,
Chloride – Wikipedia,
Chlorides – an overview | ScienceDirect Topics

Each compound has different characteristics, and only by selecting the characteristics of the compound suitable for a specific situation can the compound be applied on a large scale. 60811-18-9, name is 4-Bromo-1-chloro-2-fluorobenzene, This compound has unique chemical properties. The synthetic route is as follows., Formula: C6H3BrClF

EXAMPLE 219 (+)-(4aR)-(10bR)-4-methyl-8-(4-chloro-3-fluorophenyl)-10b-methyl-1,2,3,4,4a,5,6,10b-octahydrobenzo[f]quinolin-3-one STR237 A 15 mL round bottom flask was charged with (+)-(4aR)-(10bR)-4-methyl-10b-methyl-1,2,3,4,4a,5,6,10b-octahydrobenzo[f]quinolin-3-one-8-boronic acid (178 mg, 0.65 mmol), tetrakis(triphenylphosphine)palladium(0) (23 mg, 0.02 mmol), 1-bromo-4-chloro-3-fluorobenzene (136 mg, 0.65 mmol), 0.65 mL of 2M sodium carbonate and 2 mL of THF, fitted with a reflux condenser, and the stirred mixture was heated at 80, under nitrogen, for 24 h. The mixture was cooled, diluted with ethyl acetate (75 mL) and washed with brine (2*25 mL). The combined organic extracts were dried over sodium sulfate, concentrated, and purified by silica gel chromatography (ethyl acetate eluent) to give 125 mg (56%) of the title compound as an amorphous foam. FDMS: m/e=357. alpha[D]589 =+74.28 (c=0.35, chloroform).

According to the analysis of related databases, 60811-18-9, the application of this compound in the production field has become more and more popular.

Reference:
Patent; Eli Lilly and Company; US5578724; (1996); A;,
Chloride – Wikipedia,
Chlorides – an overview | ScienceDirect Topics

In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact. 60811-18-9, name is 4-Bromo-1-chloro-2-fluorobenzene belongs to chlorides-buliding-blocks compound, it is a common compound, a new synthetic route is introduced below. category: chlorides-buliding-blocks

Magnesium (2.43 g) and iodine (10 mg) were added to tetrahydrofuran (40 ml) and a solution of 4-bromo-1-chloro-2-fluorobenzene (21.0 g) in tetrahydrofuran (40 ml) was added dropwise, and the mixture was stirred at room temperature for 1 hr to give a Grignard’s reagent. The reaction mixture was ice-cooled and copper iodide (1.90 g) was added. 3-Chloro-2-methyl-1-propene (14.8 ml) was added and the mixture was stirred at room temperature for 1 hr. The reaction mixture was ice-cooled and saturated aqueous ammonium chloride solution (10 ml) was added. The mixture was stirred at room temperature for 20 min and magnesium sulfate (40 g) was added. The reaction mixture was filtered and the filtrate was concentrated under reduced pressure. Hexane (100 ml) was added to the obtained residue and insoluble materials were filtered off. The resulting solution was concentrated under reduced pressure to give the title compound (16.9 g). 1H-NMR (300 MHz, deltappm, CDCl3) 7.40-7.20(1H, m), 6.99(1H, dd, J=9.9, 1.8 Hz), 6.91(1H, d, J=8.1 Hz), 4.84(1H, s), 4.73(1H, s), 3.28(2H, s), 1.66(3H, s).

The synthetic route of 60811-18-9 has been constantly updated, and we look forward to future research findings.

Reference:
Patent; JAPAN TOBACCO INC.; US2005/32796; (2005); A1;,
Chloride – Wikipedia,
Chlorides – an overview | ScienceDirect Topics

Related Products of 60811-18-9, These common heterocyclic compound, 60811-18-9, name is 4-Bromo-1-chloro-2-fluorobenzene, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc, below Introduce a new synthetic route.

1-Bromo-4-chloro-3-fluorobenzene (1 g, 4.8 mmol), bis(pinacolato)diboron (1.33 g, 5.3 mmol), potassium acetate (1.4 g, 14.3 mmol) and bis(triphenylphosphine)palladium dichloride (0.2 g, 0.29 mmol) were suspended in dioxane (20 ml). The yellow suspension was flushed with argon for 30 minutes and refluxed for 12 hours. The reaction mixture was cooled to room temperature, diluted with ethyl acetate, washed with brine, dried over Na2SO4 and concentrated in vacuo. The residue was chromatographed over silica gel (hexane-ethyl acetate 99:1) to provide 2-(4-chloro-3-fluoro-phenyl)-4,4,5,5-tetramethyl-[1,3,2]dioxaborolane (0.7 g, 59%) as a colorless oil, MS: m/e=256.2 (M+).

Statistics shows that 4-Bromo-1-chloro-2-fluorobenzene is playing an increasingly important role. we look forward to future research findings about 60811-18-9.

Reference:
Patent; Buettelmann, Bernd; Neidhart, Marie-Paule Heitz; Jaeschke, Georg; Pinard, Emmanuel; US2003/229096; (2003); A1;,
Chloride – Wikipedia,
Chlorides – an overview | ScienceDirect Topics

Synthetic Route of 60811-18-9, In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact. 60811-18-9, name is 4-Bromo-1-chloro-2-fluorobenzene belongs to chlorides-buliding-blocks compound, it is a common compound, a new synthetic route is introduced below.

(7) Metal magnesium in an amount of 12 g was suspended in 10 ml of THF under nitrogen gas stream, and a solution prepared by dissolving 10.3 g of 3-fluoro-4-chloro-bromobenzene in 50 ml of THF was added dropwise thereto and stirred at room temperature for 1 hour to prepare a solution of Grignard reagent. In 50 ml of THF was dissolved 10.6 of the 4-(2-(trans-4-(2-(4-n-propylphenyl)ethyl)cyclohexyl)ethyl)iodobenzene, and 1 g of palladium chloride was added thereto and stirred under a reflux. The solution of Grignard reagent prepared in the previous procedures was added dropwise thereto and reacted while stirring for 2 hours. Reaction solution thus obtained was added to 200 ml of dilute hydrochloric acid, and the product was extracted with 200 ml of heptane. Organic layer was washed with water and dried over anhydrous magnesium sulfate, and the solvent was distilled off under a reduced pressure to obtain a yellow-brown oily product. This product was purified by a column chromatography over an alumina by using heptane as an eluent, and further recrystallized from heptane to obtain 2 g of the subject compound. According to the procedures mentioned above, the following Compounds No. 128 to 189 were synthesised:

In the field of chemistry, the synthetic routes of compounds are constantly being developed and updated. I will also mention this compound in other articles, 4-Bromo-1-chloro-2-fluorobenzene, other downstream synthetic routes, hurry up and to see.

Reference:
Patent; Chisso Corporation; US5858275; (1999); A;,
Chloride – Wikipedia,
Chlorides – an overview | ScienceDirect Topics

Some common heterocyclic compound, 60811-18-9, name is 4-Bromo-1-chloro-2-fluorobenzene, molecular formula is C6H3BrClF, traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc, below Introduce a new synthetic route. Product Details of 60811-18-9

[Example 23] (Preparation of 4′-(trans-4-n-pentyl-4-silacyclohexyl)-4-chloro-3-fluorobiphenyl) 6.5 g (20 mmol) of p-(trans-4-n-pentyl-4-silacyclohexyl) bromobenzene was dripped into a mixture of 0.5 g of magnesium (21 mmol) and 30 ml of THF to obtain a Grignard’s reagent. This solution was then dripped into a 50 ml THF solution of 4.2 g (20 mmol) of 4-chloro-3-fluoro-1-bromobenzene and a catalytic amount of tetrakis (triphenylphosphine) palladium (0) to obtain 4′-(trans-4-n-pentyl-4-silacyclohexyl)-4-chloro-3-fluorobiphenyl. This was then purified by means of chromatography to obtain 6.8 g of the target product (yield 98%). IR (liquid film) numax: 2953, 2916, 2870, 2108, 1479, 1396, 1200, 985, 879 and 812 cm-1

These compound has a wide range of applications. It is believed that with the continuous development of the source of the synthetic route 60811-18-9, its application will become more common.

Reference:
Patent; Shin-Etsu Chemical Co., Ltd.; US5659059; (1997); A;,
Chloride – Wikipedia,
Chlorides – an overview | ScienceDirect Topics

Synthetic Route of 60811-18-9,Some common heterocyclic compound, 60811-18-9, name is 4-Bromo-1-chloro-2-fluorobenzene, molecular formula is C6H3BrClF, traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc, below Introduce a new synthetic route.

a. 4-chloro-3-fluorobenzoylpropionic acid To a solution of succinic anhydride (6.0 g) in tetrahydrofuran (60 ml) was added dropwise the Grignard prepared from 1.5 g (0.062 mole) of magnesium turnings and 10.5 g (0.05 mole) of 1-bromo-4-chloro-3-fluorobenzene using the procedure of part a. When the addition was completed, the resulting suspension was stirred for 2 hours at 45 C. after which water (100 ml) was added slowly and the resulting mixture was acidified with concentrated hydrochloric acid to pH=1. The ether layer was separated and extracted with 5% aqueous sodium hydroxide (3*100 ml). The combined aqueous solutions were washed with ether (1*100 ml). The combined basic aqueous layers were acidified with concentrated hydrochloric acid to pH 1 and extracted with ethyl acetate (3*150 ml). The combined organic extracts were washed with water (1*150 ml) and brine (1*150 ml), dried over anhydrous magnesium sulfate and evaporated in vacuo to give 7.1 g (62%) of the product as a yellow orange solid. The resulting acid was converted to the desired product using the procedure of Example 11d-e. Compound 83 was prepared following essentially the same procedure.

The synthetic route of 60811-18-9 has been constantly updated, and we look forward to future research findings.

Reference:
Patent; Rohm and Haas Company; US5552409; (1996); A;,
Chloride – Wikipedia,
Chlorides – an overview | ScienceDirect Topics